Here I would be sharing step by step on how to do a ontap upgrade to 8.1.1
1) log in to the NOW site and click myautosupport, and click on the upgrade advisor and select the ontap version you are planning to.
2) you will have an option to export the steps either as an excel or an PDF.
3) Just follow the upgrade advisor.
4) The upgrade advisor will give some caution points and errors incase if you have in your setup.
5) first step is to clear those and start with the upgrade.
6) You must ensure that CPU utilization does not exceed 50% before beginning a
NDU upgrade
7) If you are running SnapDrive software on Windows hosts connected to the filer, check if the version is supported with the ontap you are upgrading.
8)Before upgrading Data ONTAP, monitor CPU and disk utilization for 30 seconds by
entering the following command at the console of each storage controller:
sysstat -c 10 -x 3
8a) Make sure that multipathing is configured properly on all the hosts.
9) Download perfstat and run it on a client as follows: perfstat -f filername -t 4 -i 5 > perfstatname.out
10) Download the system files for 8.1.1 (811_q_image.tgz) from Netapp site
11) Make sure you upgrade all the disks to the latest firmware atleast 24 hrs before the Ontap upgrade.
12) Contact NetApp Support and check /etc/messages for any obvious errors; e.g. disk
errors, firmware errors, etc
13) Back up the etc\hosts and etc\rc files in Windows to a temporary directory.
14)Copy the system image file (811_q_image.tgz) to the /etc/software directory on the
node. From a Windows box as an Administrator.
15) Before starting the upgrade send an ASUP as options autosupport.doit "starting_NDU 8.1.1"
16) software update 811_q_image.tgz -r
If you are performing a Data ONTAP NDU (or backout), you must perform this step on
both nodes before performing the takeover and giveback steps.
17) Check to see if the boot device has been properly updated:
controller1> version -b
The primary kernel should be 8.1.1.
18)Terminate CIFS on the node to be taken over (controller2 in this case):
controller2> cifs terminate
19) controller1> cf takeover
20) Wait 8 minutes before proceeding to the next step.
Doing so ensures the following conditions:
- The node that has taken over is serving data to the clients.
- Applications on the clients have recovered from the pause in I/O that occurs during
takeover.
- Load on the storage system has returned to a stable point.
- Multipathing (if deployed) has stabilized.
After controller2: reboots and displays "waiting for giveback", give back the
data service:
21) controller1> cf giveback
22) Terminate CIFS on the node to be taken over ( controller1)
23) controler1> cifs terminate
24) From the newly upgraded node controller2, take over the data service from
controller1:
controller2> cf takeover -n
25) Halt, and then restart the first node:
Controller1> halt
controller1> bye
26) controller2> cf giveback
28) If giveback is not initiated, complete the following steps:
29) Enter the cf giveback command with the -f option:
cf giveback -f
30) controller1> version ( check if the version is updated to ontap 8.1.1)
31) controller1> options autosupport.doit "finishing_NDU 8.1.1"
1) log in to the NOW site and click myautosupport, and click on the upgrade advisor and select the ontap version you are planning to.
2) you will have an option to export the steps either as an excel or an PDF.
3) Just follow the upgrade advisor.
4) The upgrade advisor will give some caution points and errors incase if you have in your setup.
5) first step is to clear those and start with the upgrade.
6) You must ensure that CPU utilization does not exceed 50% before beginning a
NDU upgrade
7) If you are running SnapDrive software on Windows hosts connected to the filer, check if the version is supported with the ontap you are upgrading.
8)Before upgrading Data ONTAP, monitor CPU and disk utilization for 30 seconds by
entering the following command at the console of each storage controller:
sysstat -c 10 -x 3
8a) Make sure that multipathing is configured properly on all the hosts.
9) Download perfstat and run it on a client as follows: perfstat -f filername -t 4 -i 5 > perfstatname.out
10) Download the system files for 8.1.1 (811_q_image.tgz) from Netapp site
11) Make sure you upgrade all the disks to the latest firmware atleast 24 hrs before the Ontap upgrade.
12) Contact NetApp Support and check /etc/messages for any obvious errors; e.g. disk
errors, firmware errors, etc
13) Back up the etc\hosts and etc\rc files in Windows to a temporary directory.
14)Copy the system image file (811_q_image.tgz) to the /etc/software directory on the
node. From a Windows box as an Administrator.
15) Before starting the upgrade send an ASUP as options autosupport.doit "starting_NDU 8.1.1"
16) software update 811_q_image.tgz -r
If you are performing a Data ONTAP NDU (or backout), you must perform this step on
both nodes before performing the takeover and giveback steps.
17) Check to see if the boot device has been properly updated:
controller1> version -b
The primary kernel should be 8.1.1.
18)Terminate CIFS on the node to be taken over (controller2 in this case):
controller2> cifs terminate
19) controller1> cf takeover
20) Wait 8 minutes before proceeding to the next step.
Doing so ensures the following conditions:
- The node that has taken over is serving data to the clients.
- Applications on the clients have recovered from the pause in I/O that occurs during
takeover.
- Load on the storage system has returned to a stable point.
- Multipathing (if deployed) has stabilized.
After controller2: reboots and displays "waiting for giveback", give back the
data service:
21) controller1> cf giveback
22) Terminate CIFS on the node to be taken over ( controller1)
23) controler1> cifs terminate
24) From the newly upgraded node controller2, take over the data service from
controller1:
controller2> cf takeover -n
25) Halt, and then restart the first node:
Controller1> halt
controller1> bye
26) controller2> cf giveback
28) If giveback is not initiated, complete the following steps:
29) Enter the cf giveback command with the -f option:
cf giveback -f
30) controller1> version ( check if the version is updated to ontap 8.1.1)
31) controller1> options autosupport.doit "finishing_NDU 8.1.1"
No comments:
Post a Comment